• 论文
主办单位:煤炭科学研究总院有限公司、中国煤炭学会学术期刊工作委员会
浅埋超大采高工作面覆岩“切落体”结构模型及应用
  • Title

    Cutting block structure model of overburden with shallow buried coal seam and ultra-large mining height working face

  • 作者

    尹希文

  • Author

    YIN Xiwen

  • 单位

    天地科技股份有限公司 开采设计事业部煤炭科学研究总院 开采研究分院

  • Organization
    1. Coal Mining and Design Department,Tiandi Science and Technology Co. ,Ltd. ,Beijing  100013,China; 2. Coal Mining and Design Branch,China Coal Research Institute,Beijing  100013,China
  • 摘要

    针对浅埋煤层矿压显现强烈,易于发生切顶压架事故的问题,以神东矿区浅埋煤层为例,统计分析了7个矿、30余个综采工作面矿压数据,结果认为,与普通埋深及深部煤层相比,浅埋煤层工作面液压支架载荷大、周期来压步距短、动载系数大。采用钻孔位移计实测分析了上湾矿88 m超大采高工作面覆岩破断及地表岩移特征,破断位置位于工作面后上方,各层位测点呈整体同时破断,破断范围快速波及地表,当工作面推进11 m后,距顶板26 m处测点最大下沉量227 mm,当工作面推进296 m后,地表最大下沉量589 m。对比分析覆岩破断与液压支架工作阻力的对应关系,认为覆岩破断后没有直接与采空区矸石接触,而是形成某种结构并产生缓慢下沉现象。采用相似模拟方法分析了上湾矿88 m超大采高工作面覆岩破断及运动规律,认为正常情况下,呈整体同时破断的块体能够相互铰接并形成结构,当支护质量不足或者遇到地质异常区时,结构易发生整体滑落失稳,导致工作面压架事故。基于以上认识,提出了浅埋超大采高工作面覆岩“切落体”结构模型,分析了切落体结构的稳定条件及失稳类型,认为浅埋煤层覆岩呈整体切落式破断,形成以滑落失稳为主的铰接结构。研究得到了液压支架合理工作阻力计算公式,并以上湾88 m工作面为例进行了验算,结果表明,基于“切落体”结构计算的支架工作阻力能够满足工作面顶板支护要求。“切落体”结构为浅埋煤层液压支架合理工作阻力确定提供了理论依据,丰富了浅埋煤层开采岩层控制理论。

  • Abstract

    Based on the data of shallow buried workface measured at 30 working faces in seven collieries,the charac- teristics of ground pressure of workface were obtained,i. e. the intensive pressure phenomenon in workface is more se- rious than that in entries,the periodical pressure step is relatively shorter,the dynamic load coefficient is larger,the curve of hydraulic support resistance is monotonic rising and falling,the collapse of overburden strata extends to sur- face directly,the maximum subsidence of the distance to roof 26 m is 227 mm after the workface advancement 11 m, the maximum subsidence of surface is 5. 89 m after the workface advancement 296 m,which is quite different from normal geotechnical condition that the ground pressure of workface is proportional to the depth of coal seams. Several observations and measurements about ground pressure were carried out in the super-high 12401 mining workface with 8. 8 m mining height in Shangwan colliery. A new model which described the broken structure of overburden in work- face was proposed as a “cutting block” model which could explain the reasons why hydraulic supports were often pres- sured into end-limited status in shallow buried geotechnical condition and obvious terraces were easily found on the surface where workface was below. In order to understand well for this new model,some physical simulations were built based on the 12401 workface practical strata in the experiment laboratory. A formula to calculate hydraulic powered supports working resistance was also derived from this model. The results were finally proved in Shangwan colliery.

  • 关键词

    浅埋工作面超大采高切落体覆岩结构模型矿压规律

  • KeyWords

    shallow buried workface;ground pressure;cutting block;overburden structure model;powered supports

  • 基金项目(Foundation)
    国家重点研发计划资助项目(2017YFC0603000,2017YFC0804300);天地科技开采设计事业部面上基金资助项目
  • DOI
  • Citation
    YIN Xiwen. Cutting block structure model of overburden with shallow buried coal seam and ultra-large mining height working face[J]. Journal of China Coal Society,2019,44(7):1961-1970.
  • 相关专题
  • 图表
相关问题

主办单位:煤炭科学研究总院有限公司 中国煤炭学会学术期刊工作委员会

©版权所有2015 煤炭科学研究总院有限公司 地址:北京市朝阳区和平里青年沟东路煤炭大厦 邮编:100013
京ICP备05086979号-16  技术支持:云智互联